Tag Archives: MEE322 Homework

Homework 4 in MEE 322: Structural Mechanics | Two-Dimensional Stress Analysis

Problem 1

The state of stress at a point is given in the figure. Find τ and τxy directly using force equilibrium. Do NOT use the stress transformation equations.

Problem 2

The state of stress at a point is given in the figure. Find σ and τxy using stress transformation equations.

Problem 3

The state of stress at a point is given in the figure. Find the principal stresses, principal directions and the maximum shear stress using

(a) Eigenvalue problem approach

(b) Stress transformation equations

Problem 4

The shaft shown in the figure has a gear at B with a force of 2098 N in -y and 6456 N in +z applied at its tip. The force along z produces a torque that drives the component attached at C, which produces an equal and opposite torque to that produced at the gear as well as forces on the shaft of 6000 N along +y and +z. The bearing at A can be considered a spherical hinge, whereas the bearing at D can be considered a planar hinge in the y-z plane.

(b) Draw bending moment and torsion diagrams for the shaft and show diagrams of the cross-section of the shaft where the critical points occur, i.e., the locations where the maximum normal stresses due to bending and maximum shear stress due to torsion coincide. Indicate the internal reactions (bending and torsion moments) in this diagram, as well as the locations of the critical points.

(b) If the diameter of the shaft is 33 mm, find the stresses at the critical point and use them to find the maximum shear stress at that location as well as the maximum and minimum principal stresses. Note: the bending normal stress can be taken as σx, while the torsion shear stress can be assumed to be τxy for the effects of this calculation, all other stresses can be assumed to be zero.

(c) It is known that the material of the shaft is such that it will fail if the maximum shear stress reaches 300 MPa. Is the shaft safe? If so, calculate the factor of safety.

Purchase the solution to this homework now

Book-Covers-2

Homework 4 in MEE 322: Structural Mechanics

This is the complete solution manual to the problems in Homework 4 of ME322: Structural Mechanics. The 4 problems included in the manual are written above. The PDF document will be sent to your email address within 24 hours from the time of purchase. The email will be coming from [email protected] Do not forget to check on your spam folder. If you have not received your file in 24 hours, kindly send us an email at [email protected]

$20.00

Homework 3 in MEE 322 Structural Mechanics | Normal and Shear Stresses Under Combined Loading Part 2

Problem 1

Three forces act on the tip of a L-shaped rod with a cross-sectional radius of 0.5 in.

(a) Determine the normal and shear stress at points A and B and draw the stress cube at those points based on the given coordinate system.

(b) Determine the maximum normal stress on the cross-section and locate the point at which it occurs.

Problem 2

The simply supported solid shaft has a radius of 15 mm and is under static equilibrium. Pulley C has a diameter of 100 mm. The pulleys B and D have the same diameter as each other. The forces on pulley B are at an angle of 45 to the negative z-axis. The forces on pulley C and pulley D are in the z and -y direction. The shaft dimensions are in mm.

(a) Determine the maximum bending and torsional stresses in the shaft.

(b) Locate the point(s) on the cross-section where the bending stress is maximum.

Problem 3

The structural part of a setup to measure net belt tensions in pulleys is shown in the figure. The belt tensions at both sides of the pulley at B (radius 10 cm) are P and F=0.1*P along z and a reaction force is measured from the pulley at C (radius 2 cm), which is connected to a load cell at E with an axial member parallel to x. Pulleys are rigidly attached to rod AD, which is made with a ductile steel rod 60 cm long and 1.27 cm in diameter. Length AB=0.20 m, and length DC=0.15 m. There is a spherical hinge at A and a plane hinge at D. The latter constrains motion in the x-z plane only.

(a) Draw bending moment and torsion diagrams for this structure as functions of the unknown tension P and use them to draw a diagram of the critical section showing internal loads (bending and torsion moments) and the critical points.

(b) Use your results from part a to determine the maximum normal stress due to bending and the maximum shear stress due to torsion in terms of the unknown tension P. Calculate the maximum value that P can have if only bending stresses are considered (with σallow = 350 MPa) and then if only torsion stresses are considered (with τallow = 175 MPa).

Purchase the Complete Solution to this Homework Now

Homework #2 in MEE 322 Structural Mechanics

This is the complete solution manual to the problems in Homework 3 of ME322: Structural Mechanics. The 3 problems included in the manual are written above. The PDF document will be sent to your email address within 24 hours from the time of purchase. The email will be coming from [email protected] Do not forget to check on your spam folder. If you have not received your file in 24 hours, kindly send us an email at [email protected]

$20.00

Homework 2 in MEE 322: Structural Mechanics | Normal and Shear Stress Under Combined Loading

Problem 1

The shaft with a circular cross-section is supported by two bearings at O and C. The bearings do not exert any moments or axial force on the shaft, and they act to constrain motion along the x and y axes. Find the minimum diameter required for the shaft if the maximum normal stress in the shaft cannot exceed 250~ \text{MPa}. All dimensions are in \text{mm}.

Problem 2

The beam ABCD shown in the figure is simply supported at A and D, and has a circular cross-section with a diameter of 80~\text{mm}. The distributed force acts at an angle of 60^\circ to the Z axis and has components only along the Z and X axis. The 1.2~\text{kN} force acts parallel to the Z axis and the 1.5~\text{kN} force acts parallel the X axis. AB = 0.6~ \text{m}, BC = 0.4~ \text{m} and CD = 1~ \text{m}.

(a) Draw shear force and bending moment diagrams for the XY and YZ planes.

(b) Determine the maximum tensile and compressive bending stress in the beam and show their locations on the cross-section of the beam.

Problem 3

The following steel structure will be made with a round bar 35~\text{mm} in diameter, such that section A-C is parallel to the y-axis and section B-E is parallel to x-axis.

An unknown moment T parallel to y is applied at point A, where there is also a spherical (ball) hinge, which constraints translations along x, y, and z axes. The plane hinge at C is contained in the x-z plane, which means that it constrains translations along the x and z axes. The force of 1000~\text{N} at D goes in -z, the force of 500~\text{N} at D goes in -y and the force of 500~\text{N} at E goes in -x. Given these conditions and the coordinate system provided, find:

(a) Diagrams of axial force, bending moment, and torsion moments for sections A-C and B-E. Use the given coordinate system to label the planes where you are making your internal reaction diagrams (x-y, x-z or z-y) and draw the corresponding axes.

(b) Calculate the maximum normal stress due to bending in this structure. Show in a diagram the point(s) in the cross-section of the structure where this stress occurs, and include the bending moments in each axis, the resultant moment, and the neutral axis. Use the given coordinate system to show the orientation of your diagram.

(c) Calculate the maximum shear stress due to torsion in this structure. Show in a diagram the point(s) in the cross-section of the structure where this stress occurs, including the torsion moment. Use the given coordinate system to show the orientation of your diagram.

Purchase the Solution to this Homework Now!

Homework 2 in MEE 322: Structural Mechanics

This is the complete solution manual to the problems in Homework 2 of ME322: Structural Mechanics. The 3 problems included in the manual are written above. The PDF document will be sent to your email address within 24 hours from the time of purchase. The email will be coming from [email protected] Do not forget to check on your spam folder. If you have not received your file in 24 hours, kindly send us an email at [email protected]

$20.00

Homework 1 in MEE 322: Structural Mechanics | Internal Reactions in 3D and 2D Bending

Problem 1

The structure shown in Fig. 1.1 is made with a steel bar that has a rectangular cross-section 5 cm tall and 10 cm wide.

Fig 1.1. Frame supporting point and distributed load

Given the geometry, loads and supports in the structure draw the bending moment diagrams for segments A-C and D-E of the structure. Then, use the diagrams to find the critical section and calculate the maximum bending stress in segment AC.

Problem 2

The torsion rod with variable cross-section shown in Fig. 2.1 is clamped at A and carries point torques at B (4 kN.m), C (8 kN.m) and D (unknown value T) with the senses indicated in the figure. It is known that the diameter of AB is 25 mm, the diameter of BC is 50 mm and the diameter of CD is 20 mm. Furthermore, 6LAB = 6LBC = 5LCD = 1200 mm. If the shear modulus of the material is 80 GPa, find:

a) The value of T that would make the angle of twist at point C with respect to A equal to zero.

b) The maximum value of T that can applied with the sense shown such that failure does not occur for an allowable shear stress of 1.1 GPa. Can the condition from part a be achieved without failure?

Fig. 2.1: Torsion rod with variable cross-section.

Problem 3

The cantilever beam shown in Fig. 3.1 has a rectangular cross-section with h = 120 mm and b = 80 mm. The 12 kN and 10 kN forces act parallel to the x and z axis, respectively, and pass through the centroid of the beam cross-section at the locations they act. The 10 kN force acts at the free end of the cantilever, whereas the 12 kN force acts 250 mm away from the free end. The cross-section ABCD is 750 mm away from the free end.

a) Determine the magnitude and location of the maximum tensile and compressive bending stress at the cross-section ABCD and indicate the neutral axis on it.

b) If an additional force, F, is applied on the beam parallel to the z axis at a point 500 mm away from the free end, what should be its magnitude and direction to make the bending stress at point B zero?

Fig. 3.1: Cantilever beam with loads along two axes.

Purchase the Solution to this Homework Now

Homework 1 in MEE 322: Structural Mechanics

This is the complete solution manual to the problems in Homework 1 of ME322: Structural Mechanics. The 3 problems included in the manual are written above. The PDF document will be sent to your email address within 24 hours from the time of purchase. The email will be coming from [email protected] Do not forget to check on your spam folder. If you have not received your file in 24 hours, kindly send us an email at [email protected]

$20.00

Advertisements
Advertisements